Add to Cart Successfully

Item(s) added to cart

View Cart & Checkout Continue Shopping >>

Pre-Order Now
Alert Me On Arrival

Email me when the item arrive.

Please enter a valid email address.
Please do not repeatedly for subscription.
Alert Me On Arrival

Subscribed successfully!

Continue Shopping

Home Accessories Flight Controllers Product Detail

BOLDCLASH F4 Flight Controller OSD for JST1.25 Plug

MPU-6000 betaflight_3.5.0 JST-PH 2.0 4g compatible for BWhoop B06 Inductrix Beta75 1s whoop

SKU: 0171000187
4.6667 3 5
$16.99   $35.99
53% off

Product Description


Motor Interface jst 1.25. The flight control is not compatible with the motor plug of B06 original factory. Customers can use the 3Pin motor wire provided by us to modify.


  • Built-in OSD Interface.
  • Buzzer Interface (with buzzer).
  • Support BLheli suite ESC programming.
  • Support DHSOT ESCD-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM.
  • Power supply: 1S Current: 5A continuous and peak 6A (3 seconds)


      Flight Controller:

  • Size: 26mm x 26mm mounting hole
  • Compatible with the Inductrix quad frame, BWhoop B06 frame and mounting holes , Beta65 Pro frame, Beta75 Pro frame,
  • Firmwarebetaflight_3.5.0_MATEKF411.hex
  • CPU: STM32F411CEU6 (100MHZ,CPU Overclock 120MHZ )
  • Sensor/Gyro : MPU-6000 triaxial accelerometer / triaxial gyroscope (SPI connection)
  • Power supply: 1S battery input (DC 3.6-4.35V)
  • OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
  • Compatible Receivers signal: SBUS, IBUS, Spektrum DSM2 / DSMX, 1024/2048. not support PPM
  • Power Cable: 55mm, with JST-PH 2.0 connector.
  • Board weight: 4g


  • Power supply: 1S
  • Current: 5A continuous and peak 6A (3 seconds)
  • Support BLHeliSuite programmable
  • Factory firmware: O_L_5_REV16_6.HEX
  • Signal Support: D-shot150, D-shot300, D-shot600, Oneshot125, Multishot, PWM

Package included

  • 1 x 1S F4 Brushless Flight Controller with JST PH2.0 connector
  • 1 x 9mm Active Buzzer
  • 4 x Flight Control Screws M1.2
  • 4 x Shell Screws
  • 4 x Vibration Rubber Rings
  • 1 x JST 1.25 2P Line
  • 1 x JST 1.0 4P Line
  • 4 x JST 1.25 3PIN Line


Frame: BWhoop B06 frame

Props: 40mm 4-blades props (for Beta75 Pro frame)

Receiver: XM Receiver / XM+Receiver / Fullspeed DSMX Receiver / Futaba RX800-PRO Receiver / Flysky RX2A Pro Receiver

Motors: 0703 motors / 0603 motors


by Alfonso Camargo on March 12, 2019

Installed this FC on the original B06 77mm frame only to discover that the 2 front motor connectors are partly under the frame, so there's no way to plug them in. Also, the updated motors with the retaining ring DO NOT fit the original B06 77mm frame either. I don't know why they advertise on here that the from will work. I had to order a Mobula7 V2 75mm frame and it all went in nicely. Not perfect, but it works. Besides the above, I was able to flash the latest BetaFlight firmware on the FC, and also able to make some adjustments to the ESCs in BLheli configurator and now it's awesome. It's very fast and flies very nice. 4 stars because of the fitment issues, but otherwise 5 stars. Boldclash, please update your info and design a frame that will fit this FC

by Kevin Langlois on January 25, 2019

Loving this F4 FC , perfect for the new era 0802 19000kv motors for 65mm build on 1s batterie ! its a must to have !

by Ludwig W on January 16, 2019

The perfomance of the F4 board is good. It works perfect with the Boldclash F02 pro AIO cam. Smartaudio is no problem. All you have to do is soldering one cable from the VTX to the TX2 of the board and assign the correct UART TBS Smart Audio in betaflight.The 1 x JST 1.0 4P Line alows you to easy plug in and out your AIO F02 cam. The firmeware for this board is MATEKF411(current version: 3.5.5). This board also supporte 0802 motors and of course frsky receivers(XM+, RXSR....). All in all a good and cheap F4 brushless board. A version with 2s compatibility would be awesome !! Here is a video about it:

< 1/1 >

Write a Review


Description Reviews (3)
Thank you for shopping at We are now processing to complete your order.
Please wait a moment with patience.